This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Maxlinear GPHY module. Also add support for
kmod-polynomial, which is a dependency for this module.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the development history of Intel's drivers, the i40evf driver was later
renamed the iavf driver. For example, some documents mention that
Intel® Network Connections Software Version 24.0 renamed the i40evf
and ixlv drivers to iavf. In subsequent versions, the i40evf driver was
gradually removed, and its functions were taken over by the iavf driver.
In the Linux system, relevant configuration instructions also exist. For
instance, the User Guide for X722 Onboard Network Card states that the
i40evf driver module should be disabled, and the iavf driver should be
installed and used.
blamed commit: 5d81b28a82
Signed-off-by: xiao bo <peterwillcn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19197
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add new setting CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS which
was introduced in kernel 6.12 and allows enabling LEDs for
the Realtek RTL8366RB subdriver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit 5687f448a4.
This unfortunately is currently breaking all targets during building
as in 6.6 kernel there is
no CONFIG_NET_DSA_TAG_VSC73XX_8021Q, it was added in 6.11 AFAIK.
So they will all fail due to $(LINUX_DIR)/net/dsa/tag_vsc73xx_8021q.ko missing.
So revert until kmod is fixed.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove settings and depends that are not used anywhere.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Intel E800 series of cards, with switchdev
support enabled for lower CPU usage.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/17564
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets the boot flag for the i40e network device driver
to load it at a more early stage of the boot process.
With commit 0a47d518df,
I added a boot priority for the mlx4 and mlx5 drivers.
Also, increase those priorities because I think they
are too low since there is currently no "room" for
built-in network device drivers.
That can cause interface order, i.e., name inconsistencies,
when Mellanox ConnectX cards are inserted or removed.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
(This was a real problem I encountered with a nanopi R6S device and
an external rtl8152 usb3 network controller - the USB controller would
claim the eth1 name, causing much confusion).
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-mlxsw-spectrum driver activated CONFIG_DCB indirectly already
on all targets which are building this driver. All other DCB capable
driver did not activate their DCB support.
CONFIG_DCB increases the uncompressed kernel size by about 7.8KB.
CONFIG_DCB is only needed some data center Ethernet cards and not used
on normal routers. Activate it only on the x86_64 and the armsr_arm64
target which are used on normal servers or in VMs.
Link: https://github.com/openwrt/openwrt/pull/17672
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The 'kmod-stmmac-core' package is referenced by the following packages:
* kmod-dwmac-intel
* kmod-dwmac-imx
* kmod-dwmac-sun8i
The problem is that 'kmod-of-mdio' is not selectable for 'TARGET_x86'.
That means the package 'kmod-dwmac-intel' is not available on this
architecture and so the package 'kmod-dwmac-intel' could not be enabled.
To fix this remove the dependencies 'kmod-of-mdio' from 'kmod-stmmac-core'.
This is not needed on this level, because the modules 'kmod-of-mdio' is
already selected by the packages 'kmod-dwmac-imx' and 'kmod-dwmac-sun8i'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This adds a kernel module package for the Marvell
MV88E6XXX DSA switch and a separate module package for
the DSA tagger since it can in theory be used by multiple
DSA switches. Enable both DSA and EDSA tags in the
tagger.
We can't just compile this in because just a few devices
has this DSA, and it depends on e.g. the I2C and SFP
to be loaded as modules first.
We have no examples of DSA switches being packaged as
modules before, all seem to be compiled in, but it
actually works just fine to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix error: Package kmod-lan743x is missing dependencies for the following libraries:
fixed_phy.ko
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Build and package driver for MediaTek PCIe 5G WWAN modem T7xx device
available in Linux 6.1 and 6.6 as kmod-mtk-t7xx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adapt netdevices kmods for building under kernel 6.6:
* Add missing module dependency for kmod-stmmac-core on kmod-of-mdio.
* Invert criteria to allow Airoha EN8811H PHY driver to build with
Linux 6.1 as well as Linux 6.6.
* Mellanox mlx5 driver started exposing thermal sensors and now it requires
hwmon
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
