Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for I-O DATA WN-DAX3000GR to update bootdelay variable while
sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for ELECOM WRC-X3000GS2 to update "bootdelay" variable
configured as "0" by default when sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
