The same function is used twice, so let's make it common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
