qualcommax: ipq50xx: Add support for Yuncore AX830
Specifications:
SOC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
Memory: 512MB DDR3L
Standard: 802.11ax/ac/b/g/n
Flash: SPI NOR 8MB (Winbond W25Q64DW) + NAND 128MB (Winbond W25N01GWZEIG)
2.4G Frequency: 2.4GHz - 2.484GHz
2.4G Wi-Fi standard: 802.11b/g/n/ax
5.8G Frequency: 4.9~5.9G
5.8G Wi-Fi Standard: 802.11 a/n/ac/ax
Interface:
Optional 1(Without 8081):
1 * 10/100 /1000Mbps RJ45 WAN Port and PoE port;
1* Gigabit Console port;
Optional 2(With 8081):
1 * 10/100/1000/2500Mbps RJ45 WAN port and PoE port,
1*10/100/1000Mbps LAN port
Buttons: 1 * Reset button, press 10 seconds to revert to default setting
Antenna: Build in 4*4dBi dual band MIMO Antenna
Data Rate: 3000Mbps （2.4G 600Mbps, 5.8G 2400Mbps）
End Users: 128+
2.4G RF Power: ≤ 23dBm
5.8G RF Power: ≤ 23dBm
DC: 12V----2A
PoE: 48V (IEEE 802.3at)
LED Light: Sys, WAN, LAN
Power Consumption: ≤ 20W
BACKUP YOUR STOCK FIRMWARE:
- Put openwrt-*-initramfs-uImage.itb to your
TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell
execute below commands:
```
device=ax830
mkdir -p /tmp/fw_backup; cd /tmp/fw_backup
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
dd if=/dev/${rootfs} of=rootfs_${rootfs} bs=1M
dd if=/dev/${rootfs_1} of=rootfs_1_${rootfs_1} bs=1M
cp /sys/firmware/fdt fdt.dtb
md5sum * > md5sum
tar -cvzf /tmp/${device}.tar.gz .
sum=$(md5sum /tmp/${device}.tar.gz | cut -d' ' -f1)
mv /tmp/${device}.tar.gz /tmp/${device}_${sum}.tar.gz
echo "stock fw backup saved to: /tmp/${device}_${sum}.tar.gz"
```
- Upload/save your backup to a safe place.
STOCK FIRMWARE RECOVERY:
- Boot initramfs image
- Upload your backed-up stock fw tarball to the device
using scp or download it from the device using wget.
- Enter device ssh cli or tty and exec:
```
cd /tmp && wget <your_web_server_ip>/${stock_fw_backup}.tar.gz`
tar -xpzf ${stock_fw_backup}.tar.gz
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f /tmp/rootfs_${rootfs}
ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_1_${rootfs_1}
reboot
```
INSTALLATION:
1. initramfs method
- Put openwrt-*-initramfs-uImage.itb to your
TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell
execute below commands:
```
cd /tmp && wget <your_web_server_ip>/factory.ubi`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat /dev/${rootfs_1} -y -f factory.ubi
reboot
```
2. u-boot factory.ubi image method
- Put factory.ubi to your TFTP server and
enter u-boot cli and exec these commands:
```
tftpboot <your_tftp_server_ip>:factory.ubi
#After downloading is finished:
flash rootfs
flash rootfs_1
reset
```
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/18968
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
Shubham Vishwakarma
Robert Marko
parent
6716fbb122
commit
52e339b8ed
8 changed files with 535 additions and 0 deletions
|
|
@ -25,6 +25,11 @@ xiaomi,ax6000)
|
|||
ubootenv_add_mtd "0:appsblenv" "0x0" "0x10000" "0x20000"
|
||||
ubootenv_add_sys_mtd "bdata" "0x0" "0x10000" "0x20000"
|
||||
;;
|
||||
yuncore,ax830)
|
||||
idx="$(find_mtd_index 0:APPSBLENV)"
|
||||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
|
|
|
|||
|
|
@ -84,6 +84,7 @@ ALLWIFIBOARDS:= \
|
|||
xiaomi_ax6000 \
|
||||
xiaomi_ax9000 \
|
||||
yyets_le1 \
|
||||
yuncore_ax830 \
|
||||
yuncore_ax880 \
|
||||
yuncore_fap650 \
|
||||
zbtlink_zbt-z800ax \
|
||||
|
|
@ -250,6 +251,7 @@ $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
|||
$(eval $(call generate-ipq-wifi-package,xiaomi_ax6000,Xiaomi AX6000))
|
||||
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
||||
$(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1))
|
||||
$(eval $(call generate-ipq-wifi-package,yuncore_ax830,Yuncore AX830))
|
||||
$(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880))
|
||||
$(eval $(call generate-ipq-wifi-package,yuncore_fap650,Yuncore FAP650))
|
||||
$(eval $(call generate-ipq-wifi-package,zbtlink_zbt-z800ax,Zbtlink ZBT-Z800AX))
|
||||
|
|
|
|||
|
|
@ -0,0 +1,487 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Copyright (c) 2025, Shubham Vishwakarma <shubhamvis98@fossfrog.in>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq5018.dtsi"
|
||||
#include "ipq5018-ess.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "Yuncore AX830";
|
||||
compatible = "yuncore,ax830", "qcom,ipq5018";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart1;
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1 swiotlb=1 coherent_pool=2M";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system: system {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0radio";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1radio";
|
||||
};
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
q6_mem_regions: q6_mem_regions@4b000000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4b000000 0x0 0x3000000>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <5000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
// MAC0 -> GE Phy
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
mdiobus = <&mdio0>;
|
||||
phy_address = <7>;
|
||||
};
|
||||
|
||||
// MAC1 -> Uniphy --- SGMII --- QCA8081
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
mdiobus = <&mdio1>;
|
||||
phy_address = <28>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
// MAC0 -> GE Phy
|
||||
&dp1 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan";
|
||||
nvmem-cells = <&hw_mac_addr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
phy-mode = "sgmii";
|
||||
};
|
||||
|
||||
// MAC1 ---SGMII---> QCA8081
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
|
||||
label = "wan";
|
||||
phy-handle = <&qca8081>;
|
||||
nvmem-cells = <&hw_mac_addr 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio1_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
qca8081: ethernet-phy@28 {
|
||||
compatible = "ethernet-phy-id004d.d101";
|
||||
reg = <28>;
|
||||
reset-deassert-us = <10000>;
|
||||
reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&sleep_clk {
|
||||
clock-frequency = <32000>;
|
||||
};
|
||||
|
||||
&xo_board_clk {
|
||||
clock-frequency = <24000000>;
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qfprom {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "0:BOOTCONFIG";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:BOOTCONFIG1";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "0:QSEE_1";
|
||||
reg = <0x100000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1a0000 {
|
||||
label = "0:DEVCFG";
|
||||
reg = <0x1a0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1b0000 {
|
||||
label = "0:DEVCFG_1";
|
||||
reg = <0x1b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x1c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1d0000 {
|
||||
label = "0:CDT_1";
|
||||
reg = <0x1d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x1e0000 0x10000>;
|
||||
};
|
||||
|
||||
partition@1f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x1f0000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@290000 {
|
||||
label = "0:APPSBL_1";
|
||||
reg = <0x290000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@330000 {
|
||||
label = "0:ART";
|
||||
reg = <0x330000 0x70000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
hw_mac_addr: hw_mac_addr {
|
||||
#nvmem-cell-cells = <1>;
|
||||
compatible = "mac-base";
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
pinctrl-0 = <&qpic_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
nand@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
nand-ecc-engine = <&qpic_nand>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:TRAINING";
|
||||
reg = <0x00 0x80000>;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x80000 0x3e00000>;
|
||||
};
|
||||
|
||||
partition@3e80000 {
|
||||
label = "rootfs";
|
||||
reg = <0x3e80000 0x3e00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
button_pins: button-state {
|
||||
pins = "gpio38";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio1_pins: mdio-state {
|
||||
mdc-pins {
|
||||
pins = "gpio36";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio-pins {
|
||||
pins = "gpio37";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
qpic_pins: qpic-state {
|
||||
clock-pins {
|
||||
pins = "gpio9";
|
||||
function = "qspi_clk";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
cs-pins {
|
||||
pins = "gpio8";
|
||||
function = "qspi_cs";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
data-pins {
|
||||
pins = "gpio4", "gpio5", "gpio6", "gpio7";
|
||||
function = "qspi_data";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: uart0-state {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp0_uart0";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
&tsens {
|
||||
status = "okay ";
|
||||
};
|
||||
|
||||
&q6v5_wcss {
|
||||
status = "okay";
|
||||
|
||||
memory-region = <&q6_mem_regions>;
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt",
|
||||
"ath11k/IPQ5018/hw1.0/m3_fw.mdt",
|
||||
"ath11k/QCN6122/hw1.0/m3_fw.mdt";
|
||||
|
||||
// IPQ5018
|
||||
q6_wcss_pd1: pd-1 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
resets =
|
||||
<&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_BCR>,
|
||||
<&gcc GCC_CE_BCR>;
|
||||
reset-names =
|
||||
"wcss_aon_reset",
|
||||
"wcss_reset",
|
||||
"ce_reset";
|
||||
|
||||
clocks =
|
||||
<&gcc GCC_WCSS_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_ACMT_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_M_CLK>;
|
||||
clock-names =
|
||||
"gcc_wcss_ahb_s_clk",
|
||||
"gcc_wcss_acmt_clk",
|
||||
"gcc_wcss_axi_m_clk";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 8 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 9 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 12 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 11 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
};
|
||||
|
||||
// QCN6122 5G
|
||||
q6_wcss_pd3: pd-3 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 24 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 25 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 28 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 27 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 24>,
|
||||
<&wcss_smp2p_out 25>,
|
||||
<&wcss_smp2p_out 26>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
// IPQ5018
|
||||
status = "okay";
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,ath11k-calibration-variant = "Yuncore-AX830";
|
||||
qcom,ath11k-fw-memory-mode = <1>;
|
||||
qcom,bdf-addr = <0x4c400000>;
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
// QCN6122 5G
|
||||
status = "okay";
|
||||
qcom,rproc = <&q6_wcss_pd3>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd3";
|
||||
qcom,ath11k-calibration-variant = "Yuncore-AX830";
|
||||
qcom,ath11k-fw-memory-mode = <1>;
|
||||
qcom,bdf-addr = <0x4d100000>;
|
||||
qcom,m3-dump-addr = <0x4df00000>;
|
||||
};
|
||||
|
|
@ -150,3 +150,18 @@ ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|||
endif
|
||||
endef
|
||||
TARGET_DEVICES += xiaomi_ax6000
|
||||
|
||||
define Device/yuncore_ax830
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Yuncore
|
||||
DEVICE_MODEL := AX830
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
SOC := ipq5018
|
||||
DEVICE_DTS_CONFIG := config@mp03.5-c1
|
||||
DEVICE_PACKAGES := ath11k-firmware-ipq5018 \
|
||||
ath11k-firmware-qcn6122 \
|
||||
ipq-wifi-yuncore_ax830
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_ax830
|
||||
|
|
|
|||
|
|
@ -21,6 +21,9 @@ ipq50xx_setup_interfaces()
|
|||
xiaomi,ax6000)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
yuncore,ax830)
|
||||
ucidef_set_interfaces_lan_wan "lan" "wan"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -34,6 +34,13 @@ case "$FIRMWARE" in
|
|||
xiaomi,ax6000)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
;;
|
||||
yuncore,ax830)
|
||||
caldata_extract "0:ART" 0x1000 0x20000
|
||||
label_mac=$(mtd_get_mac_binary 0:ART 0)
|
||||
ath11k_patch_mac $(macaddr_add $label_mac 2) 0
|
||||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi1.bin")
|
||||
|
|
@ -57,6 +64,13 @@ case "$FIRMWARE" in
|
|||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
yuncore,ax830)
|
||||
caldata_extract "0:ART" 0x26800 0x20000
|
||||
label_mac=$(mtd_get_mac_binary 0:ART 0)
|
||||
ath11k_patch_mac $(macaddr_add $label_mac 3) 0
|
||||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin")
|
||||
|
|
|
|||
|
|
@ -145,6 +145,13 @@ platform_do_upgrade() {
|
|||
CI_ROOT_UBIPART="rootfs"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
yuncore,ax830)
|
||||
CI_UBIPART="rootfs"
|
||||
remove_oem_ubi_volume ubi_rootfs
|
||||
remove_oem_ubi_volume bt_fw
|
||||
remove_oem_ubi_volume wifi_fw
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -1,3 +1,5 @@
|
|||
CONFIG_GPIO_WATCHDOG=y
|
||||
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
|
||||
CONFIG_GRO_CELLS=y
|
||||
CONFIG_IPQ5018_PHY=y
|
||||
CONFIG_IPQ_CMN_PLL=y
|
||||
|
|
|
|||
Loading…
Reference in a new issue