2018-09-04 00:08:01 +00:00
|
|
|
#!/bin/sh
|
|
|
|
|
#
|
|
|
|
|
# Copyright (C) 2018 OpenWrt.org
|
|
|
|
|
#
|
|
|
|
|
|
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
|
|
|
|
|
|
board_config_update
|
|
|
|
|
|
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
|
|
|
|
case "$board" in
|
ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.
Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B
Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
fis create -b 0x80060000 -l LeNgTh vmlinux_2
load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
use a hexadecimal calculator to subtract the start from the end in order
to substitute it below, with the leading "0x" to specify it in
hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
reset
10.Wait for the status LED to go solid green
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-09-01 02:28:35 +00:00
|
|
|
adtran,bsap1800-v2|\
|
|
|
|
|
adtran,bsap1840)
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_ext_a" "5GHz External Antenna A" "489" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_int_a" "5GHz Internal Antenna A" "493"
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_ext_b" "5GHz External Antenna B" "494" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_int_b" "5GHz Internal Antenna B" "495"
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_ext_c" "5GHz External Antenna C" "496" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi1_int_c" "5GHz Internal Antenna C" "497"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_ext_a" "2.4GHz External Antenna A" "505" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_int_a" "2.4GHz Internal Antenna A" "506"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_ext_b" "2.4GHz External Antenna B" "507" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_int_b" "2.4GHz Internal Antenna B" "508"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_ext_c" "2.4GHz External Antenna C" "509" "1"
|
|
|
|
|
ucidef_add_gpio_switch "wifi0_int_c" "2.4GHz Internal Antenna C" "510"
|
|
|
|
|
;;
|
2019-03-21 11:50:01 +00:00
|
|
|
comfast,cf-e5)
|
|
|
|
|
ucidef_add_gpio_switch "lte_power" "LTE Power" "14" "1"
|
|
|
|
|
ucidef_add_gpio_switch "lte_wakeup" "LTE Wakeup" "11" "1"
|
|
|
|
|
ucidef_add_gpio_switch "lte_poweroff" "LTE Poweroff" "1" "1"
|
|
|
|
|
ucidef_add_gpio_switch "lte_reset" "LTE Reset" "12" "1"
|
|
|
|
|
;;
|
2018-12-01 18:41:34 +00:00
|
|
|
dlink,dir-825-c1|\
|
|
|
|
|
dlink,dir-835-a1)
|
|
|
|
|
ucidef_add_gpio_switch "wan_led_auto" "WAN LED Auto" "20" "0"
|
|
|
|
|
;;
|
2019-03-09 01:10:25 +00:00
|
|
|
librerouter,librerouter-v1)
|
|
|
|
|
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "1" "0"
|
|
|
|
|
;;
|
2019-05-09 12:55:16 +00:00
|
|
|
tplink,archer-c25-v1)
|
|
|
|
|
ucidef_add_gpio_switch "led_control" "LED control" "21" "0"
|
|
|
|
|
ucidef_add_gpio_switch "led_reset" "LED reset" "19" "1"
|
|
|
|
|
;;
|
2019-07-20 10:49:20 +00:00
|
|
|
tplink,cpe210-v1|\
|
2019-07-20 11:03:43 +00:00
|
|
|
tplink,cpe220-v2|\
|
2019-07-20 10:49:20 +00:00
|
|
|
tplink,cpe510-v1)
|
2019-07-20 10:01:14 +00:00
|
|
|
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "20"
|
|
|
|
|
;;
|
2018-09-04 00:08:01 +00:00
|
|
|
ubnt,nanostation-ac)
|
|
|
|
|
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "3"
|
|
|
|
|
;;
|
2019-03-15 20:02:54 +00:00
|
|
|
ubnt,acb-isp)
|
|
|
|
|
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "11"
|
|
|
|
|
;;
|
ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-31 13:43:14 +00:00
|
|
|
zbtlink,zbt-wd323)
|
|
|
|
|
ucidef_add_gpio_switch "io0" "IO#0" "0"
|
|
|
|
|
ucidef_add_gpio_switch "io1" "IO#1" "1"
|
|
|
|
|
ucidef_add_gpio_switch "io2" "IO#2" "2"
|
|
|
|
|
ucidef_add_gpio_switch "io14" "IO#14" "14"
|
|
|
|
|
;;
|
2018-09-04 00:08:01 +00:00
|
|
|
esac
|
|
|
|
|
|
|
|
|
|
board_config_flush
|
|
|
|
|
|
|
|
|
|
exit 0
|
